Manufacturing Guide

Garment Final Inspection Before Shipping from Vietnam: Complete Guide

19 tháng 7, 2026Minh Pham
A factory worker inspects a navy garment beside boxes of folded clothing on a busy production floor.

A garment final inspection — also called pre-shipment inspection or finished goods inspection — is the last quality checkpoint before your order leaves a Vietnam factory. Conducted when 100% of production is complete and 80% or more of the order is packed into shipping cartons, the final inspection verifies that the garments you're paying for meet the specifications you agreed upon before you release payment and authorize shipment. It is the single most important quality safeguard available to a fashion brand sourcing from overseas.

This guide explains how final inspections work in Vietnam, what inspectors check, which AQL standards apply, and exactly how to respond when an inspection fails.

---

## What Is a Final Inspection?

A final inspection is a formal quality audit of a completed garment order, typically performed: - When production is 100% complete - When 80–100% of the order is packed into cartons - Before the factory ships the goods and before the buyer releases final payment (typically 30% T/T balance or 100% L/C payment upon shipment)

The inspection involves selecting a statistically determined sample of garments from the finished order, examining them against the approved product spec (PP sample, tech pack, and approved trim card), and issuing a formal pass or fail result.

✦ FACT: Pre-shipment inspection at AQL 2.5 detects approximately 85–90% of quality issues present in a production batch. Perfect detection is not possible without 100% inspection — which is cost-prohibitive for mass production. The goal is statistically valid confidence that the batch meets spec, not individual unit perfection.

---

## Who Conducts the Final Inspection?

### Option 1: Factory In-House QC The factory's own QC team conducts the final inspection. Advantages: no additional cost, no scheduling delay. Disadvantages: conflict of interest — factory QC is less likely to fail their own production, and the buyer has no independent verification.

Factory in-house QC is appropriate only when you have an established, high-trust relationship with the factory based on a track record of accurate self-reporting.

### Option 2: Third-Party Inspection Company

An independent inspection company (no affiliation with the factory) sends a certified inspector to the factory. This is the standard approach for most brands sourcing from Vietnam.

Major third-party inspection companies active in Vietnam:

| Company | Notes | |---|---| | **SGS** | Global leader; strong in Vietnam | | **Bureau Veritas (BV)** | Broad Vietnam coverage; consumer products specialist | | **Intertek** | Strong technical testing + inspection capability | | **QIMA** | Tech-enabled platform; strong in Asia; user-friendly booking | | **Asia Quality Focus (AQF)** | Specialist in garments; Vietnam-focused | | **TÜV Rheinland** | Strong in Europe-market compliance verification |

Typical cost: $250–$450 per man-day inspection (1 inspector for 1 day, covering approximately 300–600 pcs depending on product complexity). Most small-to-medium orders fit in 1 man-day.

### Option 3: Buyer-Appointed Inspector

Brand sends their own quality manager or a trusted agent to inspect. Best for luxury and premium brands with internal quality staff. Most cost-effective when the inspector is already in-country managing multiple orders.

### Option 4: Garmentix Internal QC with Report

For brands working with Garmentix: Garmentix conducts final inspection per AQL 2.5, photographs defects, and provides a formal QC report with measurement results, defect tally, and pass/fail determination. Available on all orders without additional charge — though brands sourcing from other factories can verify their own order results independently.

---

## When to Book the Final Inspection

Book the inspection 7–10 business days before your required FOB date: - Allows time for inspector scheduling and travel to factory - Provides time for reinspection if order fails - Does not create pressure to pass marginal-quality goods due to time urgency

**Inspection should not be booked until the factory confirms:** 1. Production is 100% complete 2. Minimum 80% of cartons are packed and sealed 3. The full order is available for inspection at the factory premises

---

## What the Final Inspection Covers

### Step 1: Carton Count and Shipment Quantity Verification Before touching a single garment, the inspector verifies: - Total carton count at factory vs. packing list - Carton markings (style, color, size, quantity) match order documents - Spot-check carton contents vs. marked quantities

### Step 2: Sample Selection (AQL Sample) Using ISO 2859-1 Inspection Level II, the inspector selects a random sample proportional to batch size:

| Batch Size | Sample Size (Level II) | |---|---| | 2–8 pcs | 2 pcs | | 9–15 pcs | 3 pcs | | 26–50 pcs | 8 pcs | | 51–90 pcs | 13 pcs | | 91–150 pcs | 20 pcs | | 151–280 pcs | 32 pcs | | 281–500 pcs | 50 pcs | | 501–1,200 pcs | 80 pcs | | 1,201–3,200 pcs | 125 pcs | | 3,201–10,000 pcs | 200 pcs |

Sample units must be pulled from a minimum of 3 different cartons (for small lots) up to 10+ cartons (for large lots) to ensure representative sampling.

### Step 3: Visual and Physical Inspection of Each Sample Unit

For each unit, the inspector checks:

**Workmanship:** - All seams (stitch density, seam type, seam puckering, skipped stitches) - Topstitching evenness and width - Thread trimming (no loose threads) - Zipper function (open/close 5×) - Button security (pull test ≥50N) - Pocket construction and depth - Hood construction and drawcord function - Hem and cuff evenness - Pressing quality

**Materials:** - Fabric surface defects (holes, stains, snags, shade variation) - GSM spot-check (3 garments minimum) - Color vs. approved lab dip (under D65 lighting)

**Trims and Labels:** - Main label presence and placement - Care/composition label content and placement - Size label presence - Hang tag attachment - Drawcord spec (material, length, tips) - Hardware spec (zipper brand/model, buttons)

**Sizing:** - Full measurement of each POM (Point of Measure) on every sample unit - Results recorded vs. specification with tolerances - Systematic deviations flagged (if all units deviate the same direction, indicates grading error)

**Packaging:** - Polybag size, seal, and labeling - Folding consistency - Hang tag attachment on polybag - Barcode scanability

### Step 4: Defect Classification

Each defect found is classified:

**Critical defect:** Endangers consumer safety or renders garment completely unusable. - Examples: metal pin or needle inside garment, chemical burn through fabric, functional failure of safety component - AQL tolerance: 0 (zero critical defects accepted — any critical defect = automatic FAIL)

**Major defect:** Significantly affects function or appearance; would likely cause return. - Examples: wrong color, hole in fabric, open seam, wrong size, zipper malfunction, stain visible from arm's length, off-spec construction type - Standard AQL: 2.5

**Minor defect:** Small imperfection unlikely to affect function or cause return. - Examples: single loose thread trimmed at inspection, very slight puckering in non-visible area, slight variation in trim attachment position within tolerance - Standard AQL: 4.0

### Step 5: AQL Decision

After inspecting the full sample, the inspector counts: - Total units with ≥1 critical defect → must be zero for pass - Total units with ≥1 major defect → compare to AQL 2.5 acceptance number - Total units with ≥1 minor defect (tally major + minor separately) → compare to AQL 4.0

**AQL 2.5 acceptance/rejection numbers for common sample sizes:**

| Sample Size | Accept (≤) | Reject (≥) | |---|---|---| | 32 pcs | 2 | 3 | | 50 pcs | 3 | 4 | | 80 pcs | 5 | 6 | | 125 pcs | 7 | 8 | | 200 pcs | 10 | 11 |

---

## Inspection Results: Pass, Conditional, or Fail

### PASS All defect counts are at or below acceptance numbers. Factory ships the order. Buyer releases payment.

### CONDITIONAL PASS Defect count slightly exceeds acceptance number but defects are concentrated (e.g., one production hour produced most defects, and those units can be identified and sorted). Inspector notes that 100% sorting of the identified sub-lot may achieve acceptance. Buyer decides: accept with sorting, or negotiate credit.

### FAIL Defect count exceeds rejection number. Buyer has several options:

**Option A: Rework and reinspection** Factory sorts 100% of order, repairs repairable defects, destroys unrepairable defects. Reinspection booked (additional cost). This delays shipment by 5–10 business days typically. Best choice when defects are reworkable and schedule allows.

**Option B: Negotiate a quantity reduction** If some cartons/lots are contaminated and some are clean, buyer accepts only the passing portion, reducing FOB value accordingly. Factory ships clean portion; defective portion held or destroyed.

**Option C: Accept with credit** Buyer accepts the order despite failure, negotiating a price reduction (typically 5–15% on the defective proportion). Appropriate when: the defect rate is only slightly over AQL, defects are minor, and arrival urgency overrides rework delay.

**Option D: Reject the order** For serious failures (systematic workmanship issues, wrong construction throughout, wrong materials). Buyer refuses to release payment; factory must rectify and reinspect at factory's cost. Significant time delay. Last resort — prevents receiving a non-conforming shipment, but disrupts your delivery schedule.

---

## Final Inspection Cost vs. Risk

For a 500-pc order at $14 FOB (total order value: $7,000): - Pre-shipment inspection cost: $280–$350 (1 man-day, QIMA or SGS) - Cost as % of order value: 4–5% - Cost of receiving defective goods and shipping back to Vietnam: $500–$2,000+ in freight alone (not including cost of unsellable goods, lost sales, customer returns)

The math is straightforward: a $300 inspection protects a $7,000 order. For orders above $5,000, third-party final inspection is always economically justified.

---

## Preparing Your Factory for Final Inspection

To avoid delays and ensure a smooth inspection:

**Before booking inspection, send the factory:** - Approved PP sample (reference for inspector) - Measurement chart (all POMs with tolerances) - Defect classification list (critical/major/minor per your standard) - AQL level you are applying (AQL 2.5 major is standard) - Packaging specification

**Inform the factory:** - Inspection date (allow factory 48 hours minimum notice) - Inspector name and company - Inspector will need: access to production floor, a table and adequate lighting, all order cartons available for random selection, approved PP sample available for reference

---

## Garmentix Final Inspection Process

All Garmentix orders include: - In-process inline QC at 30% and 70% production - Final inspection at 100% packed, AQL 2.5 - Written QC report with measurement results and defect photos - Photo documentation of folding, packaging, and carton marking - Report sent to buyer via email and customer portal before payment release

Buyers may also appoint their own third-party inspector (SGS, Bureau Veritas, QIMA, etc.) — access is always provided. This is Garmentix's standard policy.

Contact: info@ttgco.net | garmentix.net

---

*Garmentix | Ho Chi Minh City, Vietnam | info@ttgco.net | garmentix.net* *AQL 2.5 QC Standard | Pre-shipment Inspection on All Orders | FOB HCMC*

Minh Pham

Technical Pattern Master, TT Garment Trade

12 years in garment pattern-making and product development. Expert in tech pack creation, grading, and production-ready specifications for OEM/ODM manufacturing.