Manufacturing Guide

What Is AQL Inspection in Garment Manufacturing? AQL 2.5 Explained

19 tháng 7, 2026Minh Pham
A garment factory worker checks a light-colored shirt beside folded clothing while holding a clipboard and wearing a measuring tape.

AQL (Acceptable Quality Limit) is the statistical sampling standard used in garment manufacturing to determine whether a shipment meets minimum quality requirements without inspecting every single unit. In practice, an inspector checks a statistically determined sample size from a production batch and counts defects. If defects fall within the AQL threshold, the shipment passes. If defects exceed it, the shipment fails and is held for 100% rework or rejection.

AQL 2.5 is the global standard for apparel — meaning a maximum 2.5% defective rate is acceptable. Garmentix applies AQL 2.5 final inspection on all orders above 200 pcs before FOB shipment.

---

## What Does AQL Stand For?

AQL stands for **Acceptable Quality Limit** — the maximum percentage of defective units in a shipment that is considered acceptable for the buyer's purposes. The AQL value is not a target; it is the upper boundary of acceptable quality.

An AQL of 2.5 means: in a statistically representative sample, if 2.5% or fewer units are defective, the shipment is conditionally acceptable. If more than 2.5% are defective, the lot is rejected.

AQL inspection is governed by the international standard **ISO 2859-1** (formerly MIL-STD-1916 / MIL-STD-105E in US military procurement), which defines the sample sizes and acceptance/rejection criteria for given AQL levels.

---

## Why AQL Inspection Instead of 100% Inspection?

For large production runs, 100% inspection is economically impractical: - A 100% inspection of 5,000 units takes approximately 250–300 person-hours - Human inspectors fatigue after extended monotonous inspection, reducing accuracy to 80–85% after 4 hours - 100% inspection cost ($3–$8/pc for labor-intensive products) may equal or exceed the value of the defects found

AQL sampling solves this by applying statistical probability. If a random sample of 200 units from a 5,000-unit lot shows 0 defects, there is a 99%+ probability that the entire lot has a very low defect rate. The mathematics of AQL sampling are validated by decades of industrial quality engineering.

✦ FACT: 100% manual inspection catches approximately 80% of defects due to inspector fatigue and attention limitations. AQL statistical sampling, combined with proper inline QC during production, outperforms pure end-of-line 100% inspection in defect-prevention terms.

---

## AQL Levels Used in Garment Manufacturing

Different defect categories are evaluated under different AQL levels:

| Defect Category | Definition | Common AQL Level | |---|---|---| | **Critical** | Defect creating safety hazard or making garment non-functional | AQL 0 (zero tolerance) | | **Major** | Defect visible to the consumer; affects marketability or wearability | AQL 2.5 | | **Minor** | Defect unlikely to cause consumer rejection; not immediately noticeable | AQL 4.0 |

**Critical defects** at AQL 0 means zero tolerance — any critical defect in the sample triggers automatic lot rejection: - Sharp metal edges (broken needle embedded) - Toxic substances (chemical contamination) - Illegal product content (prohibited dyes, harmful substances) - Severe hazards for children's products (strangulation cords)

**Major defects** at AQL 2.5 (industry standard) include: - Wrong color - Visible sewing defects (holes, broken stitches, missing seams) - Measurements outside specified tolerance - Wrong size label - Damaged fabric (runs, holes, stains) - Missing or incorrect trims (wrong zipper, missing button)

**Minor defects** at AQL 4.0 include: - Loose threads (single, not affecting seam integrity) - Slight asymmetry in non-functional areas - Minor shading between front and back panels - Slight pressing imperfection

---

## How AQL Sampling Works: Step by Step

### Step 1: Determine Lot Size

The lot is the total quantity of units presented for inspection. For a 1,000-piece order shipped in 5 cartons, the lot is 1,000 units.

### Step 2: Select Sample Size Using ISO 2859-1 Table

ISO 2859-1 provides a standard table mapping lot size to sample code letter, then to sample size. For garment inspection, **Inspection Level II (Normal)** is the default.

**Sample Size Code Letters (Inspection Level II):**

| Lot Size | Code Letter | Sample Size (AQL 2.5) | |---|---|---| | 2–8 | A | 2 | | 9–15 | B | 3 | | 16–25 | C | 5 | | 26–50 | D | 8 | | 51–90 | E | 13 | | 91–150 | F | 20 | | 151–280 | G | 32 | | 281–500 | H | 50 | | 501–1,200 | J | 80 | | 1,201–3,200 | K | 125 | | 3,201–10,000 | L | 200 | | 10,001–35,000 | M | 315 |

**Example:** A lot of 800 units → Code J → Sample size 80 units

### Step 3: Determine Acceptance/Rejection Numbers

For each AQL level, the table specifies Ac (Acceptance Number) and Re (Rejection Number):

**For a sample of 80 units at AQL 2.5:** - Major defect: Ac=5, Re=6 (if 5 or fewer major defects → Pass; if 6 or more → Fail) - Minor defect: Ac=10, Re=11 (at AQL 4.0) - Critical defect: Ac=0, Re=1 (zero tolerance)

**For a sample of 125 units at AQL 2.5:** - Major: Ac=7, Re=8 - Minor: Ac=14, Re=15

### Step 4: Inspect the Sample

The inspector selects units randomly from across the lot — from different cartons, different production batches within the lot, and different positions in stacked units. Systematic sampling (e.g., every 10th unit) reduces the risk of sampling bias.

Each unit is evaluated against the AQL defect classification list (provided by the buyer or agreed in the purchase order).

### Step 5: Count Defects and Apply Decision Rule

The inspector counts the number of defective units (not the number of individual defects — one unit with three issues is still one defective unit).

- If defective units ≤ Ac → **PASS** (shipment conditionally released) - If defective units ≥ Re → **FAIL** (shipment held for rework or rejection)

---

## AQL Defect Classification for Garments: Full List

### Critical Defects (AQL 0 — Zero Tolerance) - Embedded broken needle - Chemical contamination (formaldehyde above limits, prohibited AZO dyes) - Cord/drawstring violations on children's products (EU EN 14682) - Sharp metal protrusions (unfinished rivets, exposed zipper teeth) - Serious labeling violations (fiber content fraud, missing country-of-origin)

### Major Defects (AQL 2.5)

**Fabric defects:** - Holes, tears, or snags in visible areas - Stains or contamination (oil, rust, grease, dye bleed) - Shading or color variation within a single garment - Incorrect fabric (wrong material, weight, or construction)

**Sewing defects:** - Open seams or missing seams - Broken stitches in structural areas - Skipped stitches in visible areas - Seam slippage beyond 5mm - Wrong seam type used (e.g., serged edge instead of flatlock) - Puckering or seam twisting that distorts garment shape

**Assembly defects:** - Wrong color assembled - Wrong size assembled vs. label - Missing required pocket - Zipper not functioning - Button missing or not properly attached (pull-off test failure) - Embroidery/print not matching approved spec

**Measurement defects:** - Any POM outside tolerance by more than the allowed deviation

**Label defects:** - Wrong care instructions - Missing care label - Wrong size label - Wrong fiber content declaration

### Minor Defects (AQL 4.0) - Single loose thread (not at structural seam) - Slight asymmetry in non-functional area - Minor pressing defect - Very slight shading in non-visible area - Light scuff on hang tag

---

## AQL Inspection Types in Garment Manufacturing

### Pre-Production Inspection (PPI) Conducted before production begins. Verifies raw materials (fabric, trims), confirms PP sample approval, and checks factory readiness.

### During Production (DUPRO) / Inline QC Conducted when 20–50% of production is complete. Catches systematic defects before the entire order is affected. This is the most cost-effective inspection type — defects found during production cost far less to fix than after production.

### Final Random Inspection (FRI) Standard AQL inspection conducted when 100% of goods are produced, packed, and ready for shipment. The most common inspection type ordered by brands.

✦ FACT: A major defect found during DUPRO (inline inspection) typically costs $0.50–$2.00 to fix per unit. The same defect found at final inspection costs $2–$8 per unit after unpacking, rework, and repacking.

### Container Loading Supervision (CLS) Inspector witnesses carton loading into container, verifies carton quantities, and confirms seal numbers. Prevents substitution and short-shipment fraud.

---

## Who Conducts AQL Inspections?

### Factory Internal QC The factory's own QC team conducts inline and pre-shipment checks. Internal QC is essential but has inherent conflict of interest — the factory may have commercial pressure to pass a shipment that the buyer should reject.

### Third-Party Inspection (3PI) Independent inspection companies employed by the buyer. The global leaders in apparel inspection: - **Bureau Veritas (BV):** Most widely used, operates in Vietnam - **SGS:** Strong in Asia-Pacific, full garment testing capability - **Intertek:** Strong technical testing, chemical compliance - **QIMA (formerly AsiaInspection):** Digital-first, popular with small brands - **Cotecna:** Specialist in GOTS and organic textile certification

**Cost:** $180–$350 per man-day for third-party inspection in Vietnam (2025 rates). A 1,000-unit order typically requires 1 man-day.

✦ FACT: Third-party inspection typically costs 0.3–1.5% of FOB order value. Brands that skip inspection to save this cost average 3–8× higher return rates and customer service costs post-delivery.

---

## How to Read an AQL Inspection Report

A standard AQL inspection report includes:

1. **Order identification:** PO number, style, color, size range, inspection date 2. **Quantity information:** PO quantity, quantity produced, quantity inspected (sample size) 3. **Measurement verification:** Actual vs. spec measurements for the sample size 4. **Defect summary table:** Each defect found, classification (critical/major/minor), quantity 5. **AQL result per defect category:** Pass/Fail for each category 6. **Overall result:** PASS / FAIL / CONDITIONAL PASS 7. **Photo evidence:** Photos of each major and critical defect found 8. **Inspector name and signature**

**Reading the result:** - **PASS:** All AQL categories pass; shipment can proceed - **CONDITIONAL PASS:** Some minor issues noted; buyer discretion to release - **FAIL:** One or more AQL categories failed; shipment should not proceed without corrective action

---

## What Happens When AQL Inspection Fails?

When an AQL inspection fails, the buyer has three options:

**Option 1: 100% Inspection + Rework** The factory conducts 100% inspection of all units, repairs all defective units, and presents for re-inspection. Factory bears labor cost for defects that are their responsibility. Adds 5–10 days.

**Option 2: Negotiate a Price Reduction** For minor failures or borderline results, buyer accepts the shipment at a discounted price, accepting some residual defect risk. Practical for small-value orders.

**Option 3: Reject and Cancel** For critical failures (wrong product, wrong materials, systematic construction failures), buyer rejects the lot and triggers PO dispute resolution per purchase order terms. Factory must rework and re-tender for inspection at their cost.

✦ FACT: In Vietnam, the most common reason for AQL failure is measurement deviation (39%), followed by sewing defects (28%), and trim/label issues (19%), based on Garmentix's own QC data from 2024.

---

## AQL at Garmentix

Garmentix applies the following QC structure on all orders:

| Stage | What We Do | |---|---| | **Inline QC** | Internal QC at 30% and 70% production completion — catches systematic defects early | | **Measurement Check** | Garment measurements checked against tech pack at production start and end | | **Final AQL 2.5** | Standard AQL 2.5 final inspection on all orders ≥200 pcs before FOB | | **Photo/Video Report** | Photo QC report sent to buyer before FOB shipment | | **Third-Party Option** | Garmentix coordinates access for buyer's 3PI inspector (Bureau Veritas, SGS, Intertek, QIMA) |

For orders above $15,000 FOB value, Garmentix recommends third-party inspection as a standard practice. We provide inspection scheduling coordination at no additional charge.

Contact: info@ttgco.net | garmentix.net

---

*Garmentix | Ho Chi Minh City, Vietnam | info@ttgco.net | garmentix.net* *OEM/ODM apparel manufacturing | MOQ from 200 pcs | AQL 2.5 standard QC on all orders*

Minh Pham

Technical Pattern Master, TT Garment Trade

12 years in garment pattern-making and product development. Expert in tech pack creation, grading, and production-ready specifications for OEM/ODM manufacturing.